1x KP-1 Cable (choose cable type before adding to cart)
- KP-1 CNC Touch Probe features:
- Centroid's proven Kinematic Seat Technology
- Screw on Stylus
- 360 view Green and Red LED indicator
- Poly Carbonate Body
- Stainless Steel mounting shaft
- Patented Concentric Alignment
- Works with all CNC12 Probing and Digitizing Cycles
- Set parts zeros, make measurements, digitize part and features
- USB-C connector
- Made in USA
*** Important: Bulkhead to System (Allin1DC/Oak/MPU11/M400/M39) Cable sold separately, available here.
If you currently use a Probe with your Allin1DC/Oak/MPU11/M400/M39 system, you may already have a Bulkhead to System Cable. Please check your system before purchase. KP-1 Users Manual
Part, Vise and Fixture Probing: Automatically Set Zero points fast and accurate.
3 axis CNC Touch Probe triggers in all directions. Use the KP-1 probe to quickly and accurately find zero points on a vise, fixture or part. Eliminate operator error when setting zero points, finding edges, or center locations of bosses or bores, slots and webs. Eliminates the need for a center finder or an edge finder. You'll never have to spend 30 minutes using a center finder to locate the center of a bore again. The probe will find and set the center of a bore in just seconds. In addition, the probe can be used to verify part dimensions and locations, 3D digitizing and many other applications. The KP-1 mounts in any 1/2" tool holder and has concentric adjustment screws. Also compatible with Mach3/4, WinCNC, LinuxCNC, Pathpilot and others.
KP-1 Specifications
-Probing directions X+/-, Y+/-, Z-
-Unidirectional repeatability (2 sigma) 0.0001” (2.54 micron)
-Practical use results on a good milling machine .0005”
-Probe deflection force (X,Y) 3 ounce minimum with 40mm stylus
-Probe deflection force (Z) 15 ounce minimum
-Probe body diameter and length D= 1.625” (41.275mm) L= 1.68” (42.672mm)
-Mounting shank diameter and length D= 0.5” (12.7mm) L= 1.47” (37.3mm)
-Stylus mount thread M3 thread
-LED status indicator: Red when triggered, Green when not triggered or when powered.
-Weight of probe and ½”shank 0.40 lb
-Over travel limit angle (X,Y) +/- 12 degrees from vertical
-Over travel limit (Z-) 0.25” (6.25mm)
-Patented concentric alignment (spindle/tool holder/probe body run out adjustment)
-The KP-1 Probe closes the input on the CNC controller when triggered.
-The KP-1 Probe is equipped with a detection wire so the CNC control knows that the probe is plugged in
-Works with Centroid's Probe Protection mode which prevents probe crashes while user is jogging
Part, Vise and Fixture Probing: Automatically Set Zero points fast and accurate.
Use the KP-3 probe to quickly and accurately find zero points on a vise, fixture or part. Eliminate operator error when setting zero points, finding edges, or center locations of bosses or bores, slots and webs. Eliminates the need for a centerfinder or an edgefinder. You'll never have to spend 30 minutes using a center finder to locate the center of a bore again. The probe will find and set the center of a bore in just seconds. In addition, the probe can be used to verify part dimensions and locations and many other applications. The KP-3 mounts in any 1/2" or 10mm tool holder and has concentric adjustment screws. Also compatible with Mach3/4, WinCNC, LinuxCNC, Pathpilot and others.
Replacement or additional probe tips can be purchased here.
Part, Vise and Fixture Probing: Automatically Set Zero points fast and accurate.
Use the KP-3 probe to quickly and accurately find zero points on a vise, fixture or part. Eliminate operator error when setting zero points, finding edges, or center locations of bosses or bores, slots and webs. Eliminates the need for a centerfinder or an edgefinder. You'll never have to spend 30 minutes using a center finder to locate the center of a bore again. The probe will find and set the center of a bore in just seconds. In addition, the probe can be used to verify part dimensions and locations and many other applications. The KP-3 mounts in any 1/2" or 10mm tool holder and has concentric adjustment screws. Also compatible with Mach3/4, WinCNC, LinuxCNC, Pathpilot and others.
Replacement or additional probe tips can be purchased here.
KP-3 Specifications
-Probing directions X+/-, Y+/-, Z-
-Unidirectional repeatability (2 sigma) 0.00006” (1.5 micron)
-Practical use results on a good milling machine .0005”
-Probe deflection force (X,Y) 3 ounce minimum with 40mm stylus
-Probe deflection force (Z) 15 ounce minimum
-Probe body diameter and length D= 1.35” (34.3mm) L= 2.16” (54.9mm)
-Mounting shank diameter and length D= 0.5” (12.7mm) L= 1.47” (37.3mm)
-Stylus mount thread M3 thread
-Power supply required: none
-LED status indicator red when triggered (powered by input 1ma)
-Weight of probe and ½”shank 0.40 lb
-Over travel limit angle (X,Y) +/- 12 degrees from vertical
-Over travel limit (Z-) 0.25” (6.25mm)
-Environmental IP64
-Patented concentric alignment (spindle/tool holder/probe body run out adjustment)
Part, Vise and Fixture Probing: Automatically Set Zero points fast and accurate.
Use the KP-3 probe to quickly and accurately find zero points on a vise, fixture or part. Eliminate operator error when setting zero points, finding edges, or center locations of bosses or bores, slots and webs. Eliminates the need for a centerfinder or an edgefinder. You'll never have to spend 30 minutes using a center finder to locate the center of a bore again. The probe will find and set the center of a bore in just seconds. In addition the probe can be used to verify part dimensions and locations and many other applications. The KP-3 mounts in any 1/2" or 10mm tool holder and has concentric adjustment screws. Also compatible with Mach3/4, WinCNC, LinuxCNC, Pathpilot and others.
Replacement or additional probe tips can be purchased here.
KP-3 Specifications
-Probing directions X+/-, Y+/-, Z-
-Unidirectional repeatability (2 sigma) 0.00006” (1.5 micron)
-Practical use results on a good milling machine .0005”
-Probe deflection force (X,Y) 3 ounce minimum with 40mm stylus
-Probe deflection force (Z) 15 ounce minimum
-Probe body diameter and length D= 1.35” (34.3mm) L= 2.16” (54.9mm)
-Mounting shank diameter and length D= 0.5” (12.7mm) L= 1.47” (37.3mm)
-Stylus mount thread M3 thread
-Power supply required: none
-LED status indicator red when triggered (powered by input 1ma)
-Weight of probe and ½”shank 0.40 lb
-Over travel limit angle (X,Y) +/- 12 degrees from vertical
-Over travel limit (Z-) 0.25” (6.25mm)
-Environmental IP64
-Patented concentric alignment (spindle/tool holder/probe body run out adjustment)
1x 1" Precision Stylus Pre-travel Calibration Ring
1x 5mm x 40mm Carbide Stem, Ruby Tipped Stylus (#3360)
1x 2.5mm x 40mm Carbide Stem, Ruby Tipped Stylus (#3357)
1x Stylus Wrench
1x DP-4 to System Cable
1x DP-4 Users Manual
1x DP-4 to Centroid Controller Schematic
The CENTROID DP-4 CNC Touch probe is designed for Probing (part setup, zero location setup, and CMM type location and measurement of part geometry), component/fixture/work piece setup, inspection and 3D or 2D digitizing/surfacing. The DP-4 CNC Touch probe is made in the USA with patented technology. Manufactured of stainless steel the DP-4’s mechanism requires only a feather’s touch to trigger. The DP-4’s low trigger force allows the use of small styli for maximum detail and accuracy. Commonly used on Milling machines, Machining centers, Routers and Turning centers. The DP-4 is a state-of-the-art mechanical design and is compatible with most CNC controls and DRO’s that have a PLC input for probes and probe software. The CENTROID DP-4 is reliable and is an affordable alternative to Renishaw or Marposs touch probes. Previously sold exclusively for use with a CENTROID CNC control, now the DP-4 is available for use with other CNC controls and DRO’s such as Fagor, Haas, Fanuc, Fadal, Mazak, Mach3 and many more.
Replacement or additional probe tips can be purchased here.
For Lathe use. Quickly and accurately setup tool heights in the tool library with a push of a button. The CENTROID Lathe TT-4 automatic tool height offset touch probe is plug and play with all Centroid CNC controls. Eliminates gauge blocks, paper, and repeated measurements. Save time and increase accuracy. Fully integrated into the CNC control tool library menu, just select the tool and press auto measure to set the tool height automatically. Makes measuring all types of tools faster and more accurate. Find the longest insert in a multiple insert tool quickly. Once you start using the Lathe TT-4 you'll wonder why you waited to purchase this time saving tool. Measure just one tool or a whole group of tools at once. Can also be used in the middle of a job to measure a replacement tool. Integrated with an Automatic tool changer for batch tool measurement. The Lathe TT-4 is based on KP-3 touch probe technology and is a robust kinematic design and works with all spindles even ones that with non-conductive bearings (ceramic) or tooling that doesn't conduct (diamond).
For Lathe use. Quickly and accurately setup tool heights in the tool library with a push of a button. The CENTROID Lathe TT-4 automatic tool height offset touch probe is plug and play with all Centroid CNC controls. Eliminates gauge blocks, paper, and repeated measurements. Save time and increase accuracy. Fully integrated into the CNC control tool library menu, just select the tool and press auto measure to set the tool height automatically. Makes measuring all types of tools faster and more accurate. Find the longest insert in a multiple insert tool quickly. Once you start using the Lathe TT-4 you'll wonder why you waited to purchase this time saving tool. Measure just one tool or a whole group of tools at once. Can also be used in the middle of a job to measure a replacement tool. Integrated with an Automatic tool changer for batch tool measurement. The Lathe TT-4 is based on KP-3 touch probe technology and is a robust kinematic design and works with all spindles even ones that with non-conductive bearings (ceramic) or tooling that doesn't conduct (diamond).
For Lathe use. Quickly and accurately setup tool heights in the tool library with a push of a button. The CENTROID Lathe TT-4 automatic tool height offset touch probe is plug and play with all Centroid CNC controls. Eliminates gauge blocks, paper, and repeated measurements. Save time and increase accuracy. Fully integrated into the CNC control tool library menu, just select the tool and press auto measure to set the tool height automatically. Makes measuring all types of tools faster and more accurate. Find the longest insert in a multiple insert tool quickly. Once you start using the Lathe TT-4 you'll wonder why you waited to purchase this time saving tool. Measure just one tool or a whole group of tools at once. Can also be used in the middle of a job to measure a replacement tool. Integrated with an Automatic tool changer for batch tool measurement. The Lathe TT-4 is based on KP-3 touch probe technology and is a robust kinematic design and works with all spindles even ones that with non-conductive bearings (ceramic) or tooling that doesn't conduct (diamond).
Mill, Lathe or Router use. Quickly and accurately setup tool heights in the tool library with a push of a button. The CENTROID TT-4 automatic tool height offset touch probe is plug and play with all Centroid CNC controls. Eliminates gauge blocks, paper, and repeated measurements. Save time and increase accuracy. Fully integrated into the CNC control tool library menu, just select the tool and press auto measure to set the tool height automatically. Makes measuring all types of tools faster and more accurate. Find the longest insert in a multiple insert tool quickly. Once you start using the TT-4 you'll wonder why you waited to purchase this time saving tool. Measure just one tool or a whole group of tools at once. Can also be used in the middle of a job to measure a replacement tool. Integrated with an Automatic tool changer for batch tool measurement. The TT-4 is based on KP-3 touch probe technology and is a robust kinematic design and works with all spindles even ones that with non-conductive bearings (ceramic) or tooling that doesn't conduct (diamond). Note: Also compatible with most all other CNC controller such as but not limited to: Mach3/4, WinCNC, LinuxCNC, Pathpilot and others.
Mill, Lathe or Router use. Quickly and accurately setup tool heights in the tool library with a push of a button. The CENTROID TT-4 automatic tool height offset touch probe is plug and play with all Centroid CNC controls. Eliminates gauge blocks, paper, and repeated measurements. Save time and increase accuracy. Fully integrated into the CNC control tool library menu, just select the tool and press auto measure to set the tool height automatically. Makes measuring all types of tools faster and more accurate. Find the longest insert in a multiple insert tool quickly. Once you start using the TT-4 you'll wonder why you waited to purchase this time saving tool. Measure just one tool or a whole group of tools at once. Can also be used in the middle of a job to measure a replacement tool. Integrated with an Automatic tool changer for batch tool measurement. The TT-4 is based on KP-3 touch probe technology and is a robust kinematic design and works with all spindles even ones that with non-conductive bearings (ceramic) or tooling that doesn't conduct (diamond). Note: Also compatible with most all other CNC controller such as but not limited to: Mach3/4, WinCNC, LinuxCNC, Pathpilot and others.
Mill or Router use. Quickly and accurately setup tool heights in the tool library with a push of a button. The CENTROID TT-4 automatic tool height offset touch probe is plug and play with all Centroid CNC controls. Eliminates gauge blocks, paper, and repeated measurements. Save time and increase accuracy. Fully integrated into the CNC control tool library menu, just select the tool and press auto measure to set the tool height automatically. Makes measuring all types of tools faster and more accurate. Find the longest insert in a multiple insert tool quickly. Once you start using the TT-4 you'll wonder why you waited to purchase this time saving tool. Measure just one tool or a whole group of tools at once. Can also be used in the middle of a job to measure a replacement tool. Integrated with an Automatic tool changer for batch tool measurement. The TT-4 is based on KP-3 touch probe technology and is a robust kinematic design and works with all spindles even ones that with non-conductive bearings (ceramic) or tooling that doesn't conduct (diamond). Note: Also compatible with most all other CNC controller such as but not limited to: Mach3/4, WinCNC, LinuxCNC, Pathpilot and others.
Set up your tools in a quarter of the time it would normally take. If you often machine short-run parts and are always setting up and tearing down for a new job, the TT-1 Auto tool set will save you time while more accurately setting your tool height offsets. Save time when you have to replace a dull tool with a new one in the middle of a job. The TT-1 is completely automatic. Press “measure” and the tool will automatically touch off the TT-1 and set the tool height offset in the tool library. Works with CENTROID CNC controls and most any other CNC or DRO with a probe input. Requires conductive tooling and spindle.
Set up your tools in a quarter of the time it would normally take. If you often machine short-run parts and are always setting up and tearing down for a new job, the TT-1 Auto tool set will save you time while more accurately setting your tool height offsets. Save time when you have to replace a dull tool with a new one in the middle of a job. The TT-1 is completely automatic. Press “measure” and the tool will automatically touch off the TT-1 and set the tool height offset in the tool library. Works with CENTROID CNC controls and most any other CNC or DRO with a probe input.
Set up your tools in a quarter of the time it would normally take. If you often machine short-run parts and are always setting up and tearing down for a new job, the TT-1 Auto tool set will save you time while more accurately setting your tool height offsets. Save time when you have to replace a dull tool with a new one in the middle of a job. The TT-1 is completely automatic. Press “measure” and the tool will automatically touch off the TT-1 and set the tool height offset in the tool library. Works with CENTROID CNC controls and most any other CNC or DRO with a probe input. Requires conductive tooling and spindle.
This website uses cookies to enhance the user experience. If you think that's ok, just click "Accept all". You can also choose what kind of cookies you want by clicking "Settings".
